Zhejiang Qianjiang Motorcycle RKV 200 Service Manual Page 115
- Page / 171
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
115
Note: See P101 for details of removal and installation.
8. 4. 5 Check of rear swingarm
Check the mounting shaft of rear swingarm and turn the shaft or measure it with a micrometer gauge after it is
placed onto a flat surface. If the shaft is bent, replace it.
*Attention
Do not attempt to straighten bent shaft.
Clean parts of rear swingarm mounting shaft with a solvent.
Check rear swingarm shaft sleeve component (2) and intermediate sleeve (3),
and if any damage is found, replace it.
8. 4. 6 Installation of rear swingarm
Installation must be initiated in the reverse sequence of disassembly.
Apply grease onto the pivot bushing.
Check rear swingarm shaft sleeve component (2) and intermediate sleeve (3).
Install chain guard.
Load the swingarm onto the frame and insert the rear swingarm,
Install the swingarm shaft nut to the specified torque force.
Install the lower fixing screw of the rear shock absorber.
Install the driving chain cover.
Install the two connecting bolts.
Install the rear wheel.
Nut, rear swingarm shaft
Torque force value : 70-83N·m
8. 5 Chain drive assembly
8. 5. 1． Disassembly
Stop the motorcycle on the flat ground, and support it securely.
Remove the connector of gear shift pedal, driving sprocket cover
and driving sprocket.
Remove the rear wheel, rear shock absorber, sprocket housing and
driving chain.
Rear swingarm shaft
- Content 2
- Preface 5
- Service Data 6
- Maintenance Regulations 7
- Identification of motorcycle 10
- Special Tools 11
- 2．Toes for chassis overhaul 14
- Specifications (QJ200-2A) 17
- Fault Diagnosis 19
- Diagnosis procedures 19
- Basic Data 47
- Specifications 48
- Engine oil/Oil filter 50
- Spark plug 52
- Carburetor 54
- Ignition timing 54
- Engine oil 55
- Engine oil replacement 56
- Drive chain slackness 56
- Front brake clearance 57
- Brake pedal clearance 57
- Headlamp 58
- Front/rear suspension 59
- Bolt/nut/fasteners 59
- Wheel rim/tire 60
- Tire Specifications 60
- Charging system 62
- Ⅰ Battery/Charging System 63
- 1.2 Fault Diagnosis 64
- 1.3 Battery 65
- 1.3.1 Battery Removal 65
- 1.3.2 Charging 65
- 1.4 Charging system 66
- 1.4.1 Short circuit test 66
- 67
- 1.6 Magneto charging coil 67
- Inspection 67
- Ignition System 70
- Ⅱ Ignition System 71
- 2.2 Fault diagnosis 72
- 2.3 Ignition system 73
- 2.3.3 Trigger 74
- 2.4 CDI Assembly 75
- 2.4.1 System Inspection 75
- 2.5 Ignition coil 75
- 2.6 Trigger 76
- Starting System 77
- Ⅲ Starting System 78
- 3.2 Fault Diagnosis 79
- 3.3 Starter Motor 79
- 3.3.4 Assembly 80
- 3.4 Starter Relay 81
- Bulbs/Switches/Instruments 82
- 4.2 Fault Diagnosis 84
- 4.5.1 Removal 85
- 4.5.2 Installation 85
- 4.6 Instrument 86
- 4.7 Main switch 86
- 4.8 Electric horn 87
- 4.9 Handle switch 87
- Front Hydraulic Brake 89
- Rear Hydraulic Brake 90
- Ⅴ Braking System 91
- 5.2 Fault Diagnosis 92
- 5.3 Front Hydraulic Brake 92
- 5.3.2 Inspection 93
- 5.3.3 Installation 93
- 5.4 Rear Hydraulic Brake 94
- 5.4.3 Installation 95
- Exterior 96
- Front wheel 98
- Steering handlebar 99
- Front fork 100
- 7. 1 Service Data 101
- 7. 2 Fault Diagnosis 101
- 7. 3 Front wheel 102
- 7. 3. 2 Check 103
- 7. 3. 3 Replacing bearing 103
- 7. 4 Steering handlebar 104
- 7. 5 Front fork 105
- 7. 5. 3 Installation 106
- Rear wheel 107
- Rear shock absorber 108
- Rear swing arm 109
- Chain drive assembly 110
- 8. 1 Service Data 111
- 8. 2Fault Diagnosis 111
- 8. 3 Rear wheel 112
- QJ200-2A Rear wheel 113
- 8. 5 Chain drive assembly 115
- 8. 5. 2． Check 116
- 8. 5. 4．Installation 117
- Seat cushion 118
- Fuel tank 119
- 9. 3 Fuel tank/Seat cushion 121
- 9. 3. 1 Disassembly 121
- 9. 3. 1 Installation 121
- X. Lubricating system 123
- 10. 2Fault Diagnosis 124
- 10. 3 Engine oil pump 125
- 10. 3. 1 Disassembly 125
- 10. 3. 2 Installation 127
- XI. Carburetor 129
- XII Cylinder head/Valve 133
- 12. 1 Service Data 134
- 12. 2 Fault Diagnosis 134
- 12. 3 Cylinder head 135
- Valve locking clamp 136
- Micrometer 136
- 12. 4 Inspection 137
- Reamer 140
- 12. 7 Installation 142
- 13. 2Fault Diagnosis 146
- 13. 3 Cylinder block 146
- 13. 4 Piston 147
- XIV Crankcase 150
- 14. 1 Service Data 151
- 14. 3 Crankcase 152
- 14.4 Clutch 154
- Shell components 155
- Center bearing support 155
- Pressure plate 155
- Plug gauge 156
- Driven friction disc 156
- Thickness 156
- Free length 156
- Needle roller bearing 157
- Principal shaft assembly 158
- Vice shaft assembly 158
- 14.4 Gearshift Mechanism 159
- Measuring point 161
- Point of measuring the 161
- Vernier caliper 163
- Width of the lock slot 163
- 14.6 Gear box assembly 164
- Wheel gear surface 165
- Drive claw 165
- ⅩⅦ Emission Control System 168
© 2020, manymanuals.com. All rights reserved. | 3.801 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals